pointer.gif (1967 bytes) Functional kits

             These are very high quality, American made kits. 

Take your time and turn these into museum quality display pieces.

* Note we try to keep these kits in stock, however due to their popularity our inventory sometimes runs out.  If not in stock please allow up to 4 weeks before shipping.



Finished
 Naval-24-s.JPG (146434 bytes)Naval-24-2s.JPG (162572 bytes)
 Click on images to see larger

Naval 24 pounder 1/18 scale

This is a smaller version of the 24 pounder shown below.  It is the same best selling cannon we've been selling for years in finished form.

Barrel length - 7 inches,  Bore - .34 caliber
Over 60 pieces - Carriage is pre assembled on a precision assembly fixture.  Stain, finish and polish to your liking.
Base is 10.25 x 7.5 inches
Weight - 3lbs

Save over $ 100 and build it yourself!

Yes, you can fire it!

$ 99.75
Please allow 2 weeks delivery 

 $ 99.75  


inches-s.JPG (287103 bytes)
Barrel only next to ruler

24kit.jpg (50288 bytes)
100 Pieces!
(Click for Close up)



rh24-1.gif (102890 bytes)

Finished

 Naval 24 Pounder

This cannon was patterned after the main armament of the most famous American frigates, the U.S.S. Constitution (Old Ironsides).  This is an exact replica of one of her long 24 pounder cannons.

This beautiful, very well made kit includes parts fabricated from solid brass (not plated) and furniture grade walnut.  You will need a little wood glue, some fine sand paper and some relaxing time.  You can polish the brass with any common brass cleaner.

Scale: 1 to 10                                  Length of piece: 12 inches
Width of piece: 4.8 inches           Barrel length: 11.2 inches
Bore diameter: .562 inches
Base dimensions: 9 x 15 inches

Included: matching walnut base, gun tackle and brass nameplate, 3 loading tools (ladle, rammer and worm), 20 cannon balls, 9-page booklet explaining the history and firing of the replica and step by step instructions.

Naval 24 pounder  $ 199.95

rh-yk2.gif (162548 bytes)

morta001.jpg (48142 bytes)
Click to see larger

morta002.jpg (80325 bytes)

rh-yk-k.gif (102033 bytes)

 Yorktown Mortar

This kit includes parts fabricated from solid brass (not plated) and furniture grade walnut.  You will need a little wood glue, some fine sand paper and some relaxing time.  You can polish the brass (or not) with any common brass cleaner.

This is a replica of a 10-inch siege mortar used by General George Washington's army in its campaign at Yorktown, the climatic battle of the American Revolutionary War.

The barrel is "sub chambered" for up to 20 grains of black powder load.  The fuse hole penetrates into the sub chamber.

Scale: 1 to 10                         Length of piece: 5.8 inches
Bore Diameter: 1 inch        Width of piece: 4.7 inches
Length of barrel: 3 inches

Included: Illustrated assembly instructions, booklet on the history of the mortar and firing of the replica.

Yorktown Mortar - Only $ 67.95

dg-fin.gif (49310 bytes)

dg-parts.gif (55138 bytes)

 Dahlgren Naval (Gun) Cannon - Functional, .30 caliber

This kit includes parts fabricated from solid brass (not plated) and furniture grade walnut.  You will need a little wood glue, some fine sand paper and some relaxing time.  You can polish the brass with any common brass cleaner.

This is a replica of the famous Dahlgren cannon. Primary Naval cannon used by both the North and South during the Civil War.  Both the Monitor and Merrimac were equipped with Dahlgren Cannon.  

Special attention paid to detail!  The kit features a functional elevation screw adjustment.  There are over 30 pieces in the kit. 

Barrel length = 5.5 inches

Dahlgren: $ - Only $ 67.95

rh-yk2_small.gif (3554 bytes)

dg-fin_small.gif (3240 bytes)

 Special - Buy all 3 of the smaller kits and save even more!

1. Naval 24 Pounder (smaller 1/18 scale version)
2. Yorktown Mortar
3. Dahlgren Gun

All 3 kits = $ 224.95